Julixing Instruments
 
Julixing Instruments

Company News

Hipot on a Complete Appliance: Why the Test Current Never Reaches Zero

Hipot on a Complete Appliance: Why the Test Current Never Reaches Zero

A hipot tester designed for a cable or a motor winding works on a resistive load: apply voltage, current settles, compare with a limit. An appliance is not a resistive load. It has Y-capacitors, a filter, a long cable and a metal chassis, and the current that flows in the first seconds has very little to do with the insulation.

What the meter is actually showing

Three currents add up in the reading. The charging current of every capacitance between the live side and the chassis, which decays exponentially with a time constant set by the capacitance and the tester output impedance. The capacitive current at the test frequency, which does not decay at all. And the resistive leakage, which is the only component the test is about.

On a typical appliance with 4.7 nF of Y-capacitance, at 1,500 V and 50 Hz, the steady capacitive current is about 2.2 mA. That is above the 5 mA trip of many testers when combined with a real leakage of 1 mA, and it is far above the 0.5 mA limit used for some product categories.

Component of test currentBehaviour over timeDepends onControllable by
Charging currentDecays in 0.1 to 2 sCapacitance, output impedanceRamp rate, DC test
Capacitive current at 50 HzSteadyCapacitance, voltage, frequencyDC test, lower voltage
Resistive leakageSteady, temperature dependentInsulation conditionThe thing being measured
Corona and partial dischargePulsesAir gaps, humidityGeometry, drying

Four ways to get a usable measurement

Raise the trip limit with a documented justification. This is legitimate when the capacitance is known and the limit is set above the capacitive current but below the level that would indicate a fault. It requires the number to be written down, and it requires the same limit for every unit of that model.

Test with DC. After the initial charge, the capacitive current is zero and the meter reads only resistive leakage. The test is more sensitive and less ambiguous. The compromise is that DC does not stress the insulation the way AC does, so it may miss a defect that an AC test would find.

Ramp slowly. A controlled rise over 5 to 10 s lets the charging current decay before the trip circuit is armed, which removes the false trips without changing the stress. Most modern testers have this as a setting that nobody turns on.

Test the component, not the appliance. For production screening, a test on the sub-assembly before final assembly is faster, safer and easier to interpret. The full appliance test then becomes a verification rather than a screen.

The safety point that outranks all of the above

A hipot test on a complete appliance puts test voltage on every accessible metal part if something is wired wrong, and on the operator if the return path is not solid. The tester must be one designed for appliance testing, with a proper return lead, a discharge circuit and an interlocked enclosure. A component tester with clip leads is not that instrument, and the fact that it has the right voltage range does not make it one.

  • Return lead connected to the chassis before the high lead is applied.
  • Discharge time after the test stated and enforced; a capacitor holds a charge.
  • Test station enclosed or interlocked, never a bare bench with two probes.
  • Operator trained on what a trip means, and instructed not to reset and retry until it passes.

Standards referenced: IEC 60335-1 clause 13 (leakage current and dielectric strength at working temperature) and clause 16 (at room temperature), IEC 61010-1 clause 6.3 for the corresponding requirements on measuring equipment.

    Standard:       IEC 61032 IEC 60061 IEC 60335 IEC 60529 IEC 60068 IEC 60695 VDE 0620 UL AS/NZS3112
    TAG:
IEC Test Probe Go No Go Gauge Spring Impact Hammer Integrating Sphere UL Probe Test IP Tester Test Equipment
 
Glow Wire Tester Impact Test Hammer Go Gauge UL Test Finger Probe Hipot Tester Test Probe Needle Impact Testing Machine
  Español   Español Svenska   Svenska لعربية   لعربية русский   русский Português   Português China  中国 Polski   Polski Română   Română Dansk   Dansk suomi   suomi
  Français   Français hrvatski   hrvatski Ελληνικά   Ελληνικά Nederlands   Nederlands česky   česky Deutsch   Deutsch Japan   日本の Italia   Italia български   български นไทย   นไทย
test probe