Julixing Instruments
 
Julixing Instruments

Company News

Glow-Wire Underlay: The Tissue Paper, the Board and the Part Everyone Forgets

Glow-Wire Underlay: The Tissue Paper, the Board and the Part Everyone Forgets

The glow-wire test asks whether a material ignites and whether flaming drops fall from it. The second half of that question is answered by the underlay, which is why the standard specifies it in detail and why an underlay substituted from the stationery cupboard changes the result.

What sits under the sample

A layer of tissue paper on top of a softwood board, at a defined distance below the sample. The paper catches falling particles and shows whether they were burning; the board provides a realistic surface.

ItemSpecifiedSubstitution risk
Tissue paperWrapping tissue, specified grammagePrinter paper is heavier and does not char the same way
BoardSoftwood, 10 mm nominalPlywood or MDF changes heat conduction
Gap below sample200 mm nominalA smaller gap lets particles land cooler
Paper conditionDry, flat, no creasesCreases act as ignition initiators
Board reuseFresh surface per testCharred board ignites earlier

Why the paper matters more than it looks

A burning particle that lands on heavy paper may self-extinguish; the same particle on thin tissue ignites it. The tissue is chosen to be sensitive, so that a marginal particle is caught rather than missed. Substituting heavier paper makes the test easier.

Practical discipline

  • Keep the tissue in a sealed bag; damp tissue does not ignite reproducibly.
  • Renew the board surface every few tests, and note when it was renewed.
  • Check the 200 mm gap with a rule, not by eye.
  • Photograph the underlay after the test; it is the record of the second half of the verdict.

None of this is expensive. All of it is routinely skipped, and it is the first thing a second laboratory will ask about.

Standards referenced: IEC 60695-2-11 for the glow-wire flammability test, IEC 60695-2-10 for the apparatus.

How to tell whether the paper was the cause

If the paper ignites but the sample did not sustain flaming, the verdict usually turns on whether the particle that fell was itself burning. A particle that is glowing but not flaming will char the paper without igniting it; a flaming drop will ignite it within a second.

Video the underlay during the test. A 30 s recording settles in ten seconds what a written description cannot.

Specimen thickness and the drop path

The 200 mm gap is measured from the lowest point of the specimen to the paper, not from the glow-wire tip. A specimen mounted at an angle has its lowest point in a different place, and the gap must be measured there.

A 50 mm error in the gap changes the temperature of the falling particle by the time it lands, which changes whether it ignites the paper.

Recording the second half of the verdict

Photograph the underlay after every test, with a scale in the frame. A charred ring 10 mm across and a scorch mark 2 mm across are different results, and the written description rarely captures the difference.

Board condition between tests

Charred board conducts heat differently and ignites earlier on the second test. Sand the surface or rotate the board so each test uses a fresh area, and replace the board after about ten tests.

The 200 mm gap and the falling particle

A particle that falls 200 mm reaches the paper in about 0.2 s, arriving at close to its release temperature. Halve the gap and it arrives hotter; double it and it may have extinguished in flight. Measure the gap on the lowest point of the specimen, with a rule, every time.

    Standard:       IEC 61032 IEC 60061 IEC 60335 IEC 60529 IEC 60068 IEC 60695 VDE 0620 UL AS/NZS3112
    TAG:
IEC Test Probe Go No Go Gauge Spring Impact Hammer Integrating Sphere UL Probe Test IP Tester Test Equipment
 
Glow Wire Tester Impact Test Hammer Go Gauge UL Test Finger Probe Hipot Tester Test Probe Needle Impact Testing Machine
  Español   Español Svenska   Svenska لعربية   لعربية русский   русский Português   Português China  中国 Polski   Polski Română   Română Dansk   Dansk suomi   suomi
  Français   Français hrvatski   hrvatski Ελληνικά   Ελληνικά Nederlands   Nederlands česky   česky Deutsch   Deutsch Japan   日本の Italia   Italia български   български นไทย   นไทย
test probe