Julixing Instruments
 
Julixing Instruments

Company News

Terminal Torque Screwdriver Calibration: 0.5 to 3 Newton Metres

Terminal Torque Screwdriver Calibration: 0.5 to 3 Newton Metres

Terminal torque appears in product standards as a table of values by screw size, and in factories as a number an operator aims for by feel. IEC 60998-1 is the standard that carries the terminal tables most small connectors are checked against, and the gap between the table and the feel is where loose terminals and cracked terminal blocks come from. Both are failures that appear months after the product ships.

Why the torque matters in both directions

  • Too little torque. The connection has higher resistance, heats under load, and the heat relaxes the joint further. The result is a terminal that was correct at assembly and loose at the end of a year.
  • Too much torque. The screw strips, the terminal block cracks, or the conductor is cut. A 1.2 N.m terminal taken to 1.6 N.m is 33 percent over and is enough to crack a moulding that would survive 100 temperature cycles at the correct torque. The failure is immediate in the first case and delayed in the second, because a cracked block fails under thermal cycling.

The acceptable window is narrow, and it is narrower than most operators assume. A hand driver varied by feel typically spans plus or minus 30 percent, which on a 1.2 N.m terminal is a range from 0.85 to 1.55 N.m — enough to be outside the window in both directions.

Reading the torque table

The values in a product standard are specified for a screw of a given thread diameter and property class, with a defined type of screwdriver blade and a defined number of tightening operations. Three consequences:

  1. Size matters more than length. An M4 terminal takes a different torque from an M3 terminal regardless of how long the screw is.
  2. The blade type changes the result. A Phillips blade that cams out limits the achievable torque, so the same setting produces a different joint than a slotted blade.
  3. The number of operations matters. A terminal tightened and loosened five times before final tightening has a different friction condition — some standards specify the sequence, and it is part of the test.

Calibrating a preset driver

A preset torque driver is calibrated on a torque tester with a rotary transducer. The procedure is short but has three details that change the result:

Measurement pointMeasure at the driver's own output, with the same bit fitted that will be used in production
SpeedUse the same application speed as production. A click-type driver releases at a torque that depends on the rate of loading
RepetitionsFive releases, take the mean and note the spread. A spread of more than 5 percent means the driver is worn

Calibration frequency should follow usage. A driver used two hundred times a day needs a check monthly; a driver used twice a week needs a check annually. The trigger is release count, not the calendar.

The spring that sets the torque is the part that fails

Inside a click-type driver is a spring-loaded mechanism that releases at a set torque. The spring relaxes with use, and the release torque falls. A driver set to 1.2 N.m when new may release at 1.0 N.m after 20,000 cycles, which is a 17 percent error with no external sign.

Two habits extend the interval between adjustments:

  • Store the driver at its lowest setting, not at the production setting. A spring held compressed for months takes a set.
  • Do not use the driver as a screwdriver. Using it to loosen screws loads the mechanism in the wrong direction and changes the release point.

Verifying the joint, not just the tool

A calibrated driver and a correct setting do not guarantee a correct joint. Three checks close the loop:

  1. Mark and check. A torque mark on the screw head after tightening lets an inspector see at a glance whether a screw has been touched since.
  2. Destructive audit. Periodic re-tightening measurement on a sample: apply the specified torque to an already-tightened screw and note whether it moves. A screw that turns more than a few degrees was under-torqued.
  3. Thermal check. On a loaded sample, measure terminal temperature rise. A joint that runs hotter than its neighbours is loose, regardless of what the driver said.

Records

The record that answers the audit question has four fields: driver identification, set torque, measured torque at each of five releases, and the date. A certificate that says "within tolerance" without the measured values is a receipt, not a calibration.

The test equipment range includes torque testers and preset drivers for terminal work; the site index links the blades and bit sets used with them.

    Standard:       IEC 61032 IEC 60061 IEC 60335 IEC 60529 IEC 60068 IEC 60695 VDE 0620 UL AS/NZS3112
    TAG:
IEC Test Probe Go No Go Gauge Spring Impact Hammer Integrating Sphere UL Probe Test IP Tester Test Equipment
 
Glow Wire Tester Impact Test Hammer Go Gauge UL Test Finger Probe Hipot Tester Test Probe Needle Impact Testing Machine
  Español   Español Svenska   Svenska لعربية   لعربية русский   русский Português   Português China  中国 Polski   Polski Română   Română Dansk   Dansk suomi   suomi
  Français   Français hrvatski   hrvatski Ελληνικά   Ελληνικά Nederlands   Nederlands česky   česky Deutsch   Deutsch Japan   日本の Italia   Italia български   български นไทย   นไทย
test probe