Julixing Instruments
 
Julixing Instruments

Company News

Setting a Thread Ring Gauge to ISO 1502: Setting Plugs, Wear Allowance and Common Errors

Setting a Thread Ring Gauge to ISO 1502: Setting Plugs, Wear Allowance and Common Errors

A thread ring gauge is a fixed limit gauge, and unlike a plug gauge it cannot be checked with a micrometre. Its size is established by a setting plug. If the setting plug is worn, or the setting procedure is informal, every part inspected afterwards inherits the error.

What the setting plug does

ISO 1502 defines the gauge system for general-purpose metric threads, including the setting plugs used to set and check thread ring gauges. The GO setting plug represents the maximum material condition of the ring; the NOT GO setting plug represents the minimum. A ring gauge is correctly set when it screws onto the GO setting plug to the specified engagement and does not pass over the NOT GO setting plug.

The setting plug is a master. It is handled carefully, kept in its own case, and calibrated on a shorter interval than the working ring. Using a production plug gauge as a setting master is a common and expensive shortcut.

The sequence

  1. Clean the ring and the setting plug with a solvent that leaves no residue, then allow both to reach room temperature.
  2. Apply the GO setting plug by hand. The ring should screw on freely over the full thread length; force indicates wear or damage in the ring.
  3. Apply the NOT GO setting plug. The ring should not pass beyond the permitted number of turns; if it does, the ring is oversize and must be replaced.
  4. Record the setting, the plug identification and the temperature.
  5. Re-check at defined intervals during use, not only at the start of the shift.

Wear allowance, in plain terms

Working thread ring gauges are made with a wear allowance on the GO side: they are slightly beyond the nominal maximum so that a limited amount of wear still leaves them usable. That allowance is not a licence to keep using a worn gauge. Once the ring has worn through the allowance, it accepts parts that are outside the thread limit, and no amount of re-setting will recover it. The NOT GO side has no wear allowance in the same sense: it is a pure limit.

Ring screws onto GO setting plug with difficultyRing is undersize or damaged; remove from service
Ring passes NOT GO setting plugRing is oversize through wear; retire it
Ring screws on correctly but rejects good partsCheck part temperature, burrs and thread finish before blaming the ring

Why parts fail that should pass

Threads are sensitive to small disturbances. The usual causes of a false reject:

  • Burr at the thread start from a worn die head or a poorly deburred part.
  • Plating thickness on the thread flanks, which closes the gap by several micrometres.
  • Part temperature above the reference, expanding the thread.
  • Contamination in the ring, especially dried cutting fluid.

A ring gauge cannot tell you which of these applies. Inspect the rejected part with a thread profile projector or a thread measuring system before adjusting the process.

Traceability that survives an audit

Keep, for each ring: the ISO 1502 gauge designation, the setting plug identification, the calibration certificate for both, the setting record with date and operator, and the parts or lots inspected between settings. When a ring is found oversize, the audit trail is the only way to bound the recall. A ring with no setting record is a ring with no history, and its results cannot be defended.

The product catalogue lists thread ring and plug gauges by thread size and tolerance class, and the IPX5/IPX6 jet test apparatus covers the water-test side of the same inspection laboratory.

    Standard:       IEC 61032 IEC 60061 IEC 60335 IEC 60529 IEC 60068 IEC 60695 VDE 0620 UL AS/NZS3112
    TAG:
IEC Test Probe Go No Go Gauge Spring Impact Hammer Integrating Sphere UL Probe Test IP Tester Test Equipment
 
Glow Wire Tester Impact Test Hammer Go Gauge UL Test Finger Probe Hipot Tester Test Probe Needle Impact Testing Machine
  Español   Español Svenska   Svenska لعربية   لعربية русский   русский Português   Português China  中国 Polski   Polski Română   Română Dansk   Dansk suomi   suomi
  Français   Français hrvatski   hrvatski Ελληνικά   Ελληνικά Nederlands   Nederlands česky   česky Deutsch   Deutsch Japan   日本の Italia   Italia български   български นไทย   นไทย
test probe